Manifold flange removal.

The place to discuss all matters relating to David Brown Tractors. You will need to register your user name before you can post. If you have already registered could you please make sure that your location details have been completed. Go to My Account in the Main Menu on the left, and then go into "Edit Your Information" and complete your location details. Give the Country (and State/Province if you wish) if outside the U.K. County if within the U.K. Location details helps other members if you need spares, technical advice, or the nearest practical help.

DISCLAIMER -

David Brown Tractor Club Ltd
Forum/website Disclaimer

1. This [forum/website/chat room] and the advice and opinions expressed herein is not a solution for mechanical, electrical, valuations, other problems, breakdowns or issues experienced in relation to the vehicles referenced.

2. If reliance is thought to be placed on any of the information guidance or input provided such information will be expressly confirmed as appropriate to be relied upon.

3. In the absence of any such confirmation no reliance should be suggested or inferred.

4. Members must not disclose information to 3rd parties in anticipation that reliance will be given by non-members.

5. Non-members must not purport to give advice on behalf of David Brown Tractor Club.

6. If you or someone you know is experiencing difficulties or repeated breakdowns you must seek assistance for an appropriately qualified expert who holds themselves out as such.

7. Any comments are free of charge and made or posted on an ex gratia basis. No member or non-member may advertise their professional services

Any user inactive for more than 3 months will automatically be deactivated, please contact admin@dbtc.co.uk if you would like to be reactivated.

Please be aware that your user name and entered location can be seen by all members. We only store information you have entered which is your email address and username, your IP is also stored, we have no access to private passwords.

If you do not agree with your information being stored, please do not register an account, If you wish to unsubscribe at any time please email admin@dbtc.co.uk giving your username.

Amended 27/10/18

Moderators: Segrie61, admin

Berk
Posts: 71
Joined: Wed Nov 22, 2017 5:41 pm
Location: Carmarthenshire

Re: Manifold flange removal.

Post by Berk » Thu Aug 15, 2019 10:15 pm

As John Newman said, welding an appropriate nut on is often a decent way of freeing stuff off, heating and cooling cycles (without quenching, ideally) will break up a lot of corrosion. Differential heating is even better (heat the nut, but cool the bolt/stud) but an absolute pain in the ************ most of the time.

Left handed drills can work very well if you have a good centre and a strong nerve, but is often a complete nightmare on an item in situ (and if your 3 nuts are a problem, your manifold studs almost certainly will be just as bad)

Saying all that, we did the manifold job earlier in the year (after a low flying branch broke the manifold to exhaust casting) ended up shearing both studs, and welding nuts (M8, if I recall) onto the sheared studs. Left everything to cool then heated the manifold (with wet rags on the studs) with a mapp torch.

Came out like new bolts after that.

Scooby
Posts: 3927
Joined: Tue Jan 03, 2006 8:16 pm
Location: Warwickshire

Re: Manifold flange removal.

Post by Scooby » Fri Aug 16, 2019 7:34 am

That is very helpful. Thanks to everyone for their help. I cheated a bit yesterday though. I cleaned the bottom of the bit that goes into the flange and dribbled a few spots of weld on and then ground them down so that it would go into the flange. The exhaust is much tighter now and doesn't wobble about so much. It really needs a new one but I don't think they are the same as the originals.
ImageImage


Three is twee, four does snore, but 6 just clicks........Scooby

Gard
Posts: 239
Joined: Sun Apr 06, 2008 2:25 pm
Location: Fairfax Vermont USA

Re: Manifold flange removal.

Post by Gard » Sat Aug 17, 2019 10:47 pm

I also have had good luck welding on a nut. Sometime I just weld on a big blob and grab it with locking pliers as it is cooling down.
The wire feed mig welder is best, but stick can be used also.
If the thread is stripped, drill it to a larger size and install a thread insert.

Post Reply

Who is online

Users browsing this forum: Google [Bot], jazo, Superpuma165 and 9 guests