885 Fuel gauge - Wiring & general advice

The place to discuss all matters relating to David Brown Tractors. You will need to register your user name before you can post. If you have already registered could you please make sure that your location details have been completed. Go to My Account in the Main Menu on the left, and then go into "Edit Your Information" and complete your location details. Give the Country (and State/Province if you wish) if outside the U.K. County if within the U.K. Location details helps other members if you need spares, technical advice, or the nearest practical help.

DISCLAIMER -

David Brown Tractor Club Ltd
Forum/website Disclaimer

1. This [forum/website/chat room] and the advice and opinions expressed herein is not a solution for mechanical, electrical, valuations, other problems, breakdowns or issues experienced in relation to the vehicles referenced.

2. If reliance is thought to be placed on any of the information guidance or input provided such information will be expressly confirmed as appropriate to be relied upon.

3. In the absence of any such confirmation no reliance should be suggested or inferred.

4. Members must not disclose information to 3rd parties in anticipation that reliance will be given by non-members.

5. Non-members must not purport to give advice on behalf of David Brown Tractor Club.

6. If you or someone you know is experiencing difficulties or repeated breakdowns you must seek assistance for an appropriately qualified expert who holds themselves out as such.

7. Any comments are free of charge and made or posted on an ex gratia basis. No member or non-member may advertise their professional services

Any user inactive for more than 3 months will automatically be deactivated, please contact admin@dbtc.co.uk if you would like to be reactivated.

Please be aware that your user name and entered location can be seen by all members. We only store information you have entered which is your email address and username, your IP is also stored, we have no access to private passwords.

If you do not agree with your information being stored, please do not register an account, If you wish to unsubscribe at any time please email admin@dbtc.co.uk giving your username.

Amended 27/10/18

Moderators: Segrie61, admin

Post Reply
mikeadams1985
Posts: 53
Joined: Thu Mar 01, 2018 7:59 pm
Location: Liverpool

885 Fuel gauge - Wiring & general advice

Post by mikeadams1985 » Sat Jan 12, 2019 8:19 pm

Im making way on the full re-wire of 885, its been completely stripped out and starting from fresh. (so far switched from dyno to alternator)

Ive had to replace the fuel sender and bought a new one, tested with the multi meter and it works fine.
Fuel gauge tested and works.

Together....cant get it to work. Im either getting it reading full or nothing. No matter the position of the sender, this is all being tested on the bench using a 12v battery.

Im not convinced the wiring is correct, eventhough im following the DB wiring diagram as per the electrical diagram.

Having scanned over some old photos ive noticed what i beleive to be a voltage stabiliser/ reducer on the back of the gauge which i dont have anymore. I kind of assumed this wasnt needed now ive got a alternator on instead of dyno.

Do i need this to reduce the voltage from 12v to 10v?

User avatar
rid54
Posts: 174
Joined: Mon Oct 13, 2014 8:20 am
Location: Vallentuna, Sweden

Re: 885 Fuel gauge - Wiring & general advice

Post by rid54 » Mon Jan 14, 2019 5:10 pm

A detail: A dynamo or an alternator in this case makes no difference. Alternators can be driven at higher revs than dynamos and are normally "geared" for higher revs by having smaller belt pulleys; thus they start charging the battery quicker and keep charging even a low engine speeds. System voltage regulation aims for the same level (14,4 Volts) on both types, as this is what is needed to keep the battery happy.

Oldgustav
Posts: 47
Joined: Wed Feb 13, 2019 4:01 am
Location: Pembrokeshire

Re: 885 Fuel gauge - Wiring & general advice

Post by Oldgustav » Sat Feb 16, 2019 12:29 pm

May I ask where you obtained your 885 wiring diagram?

User avatar
cobbadog
Posts: 573
Joined: Tue Oct 11, 2011 6:18 am
Location: beautiful Coopernook NSW. near Taree. NSW. Australia

Re: 885 Fuel gauge - Wiring & general advice

Post by cobbadog » Sun Feb 17, 2019 2:58 am

As stated there will be no differnce in the power whether it is generated from an altenator or generator. 12v is 12v. Sounds more like a short somewhere in the wiring.If it worked well by connecting the wires from power to sender and gauge and then lifting the arm on the sender and the gauge worked properly then there is a short in the system somewhere giving a full reading on the gauge.

Post Reply

Who is online

Users browsing this forum: Superpuma165 and 15 guests