Cropmaster 30C brake job

The place to discuss all matters relating to David Brown Tractors. You will need to register your user name before you can post. If you have already registered could you please make sure that your location details have been completed. Go to My Account in the Main Menu on the left, and then go into "Edit Your Information" and complete your location details. Give the Country (and State/Province if you wish) if outside the U.K. County if within the U.K. Location details helps other members if you need spares, technical advice, or the nearest practical help.

DISCLAIMER -

David Brown Tractor Club Ltd
Forum/website Disclaimer

1. This [forum/website/chat room] and the advice and opinions expressed herein is not a solution for mechanical, electrical, valuations, other problems, breakdowns or issues experienced in relation to the vehicles referenced.

2. If reliance is thought to be placed on any of the information guidance or input provided such information will be expressly confirmed as appropriate to be relied upon.

3. In the absence of any such confirmation no reliance should be suggested or inferred.

4. Members must not disclose information to 3rd parties in anticipation that reliance will be given by non-members.

5. Non-members must not purport to give advice on behalf of David Brown Tractor Club.

6. If you or someone you know is experiencing difficulties or repeated breakdowns you must seek assistance for an appropriately qualified expert who holds themselves out as such.

7. Any comments are free of charge and made or posted on an ex gratia basis. No member or non-member may advertise their professional services

Any user inactive for more than 3 months will automatically be deactivated, please contact admin@dbtc.co.uk if you would like to be reactivated.

Please be aware that your user name and entered location can be seen by all members. We only store information you have entered which is your email address and username, your IP is also stored, we have no access to private passwords.

If you do not agree with your information being stored, please do not register an account, If you wish to unsubscribe at any time please email admin@dbtc.co.uk giving your username.

Amended 27/10/18

Moderators: Segrie61, admin

User avatar
ollek
Posts: 3532
Joined: Tue Apr 10, 2012 1:20 pm
Location: South West Finland

Re: Cropmaster 30C brake job

Post by ollek » Wed Apr 04, 2018 1:44 pm

There is something obstructing the reduction to be fitted to the rear axle. You must not use the bolts to get the reduction to get in contact with the rear axle. I can see in a couple of pictures you have provided, that the brake drum was I a very bad shape. Have you done anything as to get rid of the rust and make the brake drum smooth and level? A brake drum like the one in the picture needs to be rotary-cut. There is a big possibility that the brake bands are jamming against the deteriorated brake drum.

User avatar
cobbadog
Posts: 342
Joined: Tue Oct 11, 2011 6:18 am
Location: beautiful Coopernook NSW. near Taree. NSW. Australia

Re: Cropmaster 30C brake job

Post by cobbadog » Thu Apr 05, 2018 7:36 am

Hi ollek,
Thanks for your help. Yes I have cleaned the rust and dirt from the inside of the brake drum. In the end using the bolts to pull it inwards worked quite well. I mentioned that I did try that approach and I was NOT happy with it and it was getting too tight on the bolts so I stopped and tried another idea. In the end it was using the bolts that did the job and all with very little leverage on the short spanner. It was so light that it was just above being able to use your fingers to do them up. Anyway all is back together with all new seals and gaskets and new SAE140 oil in the reduction box and new oil in the gearbox with no water in the mix.
Now it is time to start preparation for paint work. this will take some time but I'm not in a hurry.
Thank you once again to all help offered on this tricky fix.

Post Reply

Who is online

Users browsing this forum: No registered users and 31 guests