Early Tvo cropmaster Help

The place to discuss all matters relating to David Brown Tractors. You will need to register your user name before you can post. If you have already registered could you please make sure that your location details have been completed. Go to My Account in the Main Menu on the left, and then go into "Edit Your Information" and complete your location details. Give the Country (and State/Province if you wish) if outside the U.K. County if within the U.K. Location details helps other members if you need spares, technical advice, or the nearest practical help.

DISCLAIMER -

David Brown Tractor Club Ltd
Forum/website Disclaimer

1. This [forum/website/chat room] and the advice and opinions expressed herein is not a solution for mechanical, electrical, valuations, other problems, breakdowns or issues experienced in relation to the vehicles referenced.

2. If reliance is thought to be placed on any of the information guidance or input provided such information will be expressly confirmed as appropriate to be relied upon.

3. In the absence of any such confirmation no reliance should be suggested or inferred.

4. Members must not disclose information to 3rd parties in anticipation that reliance will be given by non-members.

5. Non-members must not purport to give advice on behalf of David Brown Tractor Club.

6. If you or someone you know is experiencing difficulties or repeated breakdowns you must seek assistance for an appropriately qualified expert who holds themselves out as such.

7. Any comments are free of charge and made or posted on an ex gratia basis. No member or non-member may advertise their professional services

Any user inactive for more than 3 months will automatically be deactivated, please contact admin@dbtc.co.uk if you would like to be reactivated.

Please be aware that your user name and entered location can be seen by all members. We only store information you have entered which is your email address and username, your IP is also stored, we have no access to private passwords.

If you do not agree with your information being stored, please do not register an account, If you wish to unsubscribe at any time please email admin@dbtc.co.uk giving your username.

Amended 27/10/18

Moderators: Segrie61, admin

Post Reply
User avatar
glenreed
Posts: 24
Joined: Thu Aug 06, 2009 7:30 pm

Early Tvo cropmaster Help

Post by glenreed » Thu Aug 06, 2009 7:43 pm

Hello can anyone tell me what size fan belt should be fitted to my petrol tvo cropmaster (gear driven dynamo) as i have just bought my 1st tractor in bits and the belt is missing
also is there a cheaper equivilent for the Expensive K97F spark plugs?
thanks Glen

Guest

RE: Early Tvo cropmaster Help

Post by Guest » Thu Aug 06, 2009 9:28 pm

Not sure of the belt size Glen but there are others that will give you the info. As far as your plugs are concerned, any 18mm lomg reach ones will do the job, 15 to 25 thou gap. And welcome to the Forum.

Joe90
Posts: 59
Joined: Thu Aug 21, 2008 9:24 pm

TVO Cropmaster help

Post by Joe90 » Fri Aug 07, 2009 9:44 am

Glen, I bought my fan belt from www.davidbrownparts.com and very helpful they are too. I use NGK AB-2 they are compatible with K97F but are a wider heat range plug and run better especially on oil burning engines, available at low cost from Ebay via a Manchester NGK stockist. Regards Joe90.

User avatar
glenreed
Posts: 24
Joined: Thu Aug 06, 2009 7:30 pm

Post by glenreed » Fri Aug 07, 2009 10:03 pm

Cheers for your help chaps hopfuly i will be able to get delivery of the plugs tomorrow from the motor factors i use at work fingers crossed they will stock them,
Then all i have to do is put the tractor back together i was told when i bought it all it needed was 4 new plugs a fan belt and a battery to run and as far as i can see not many other bits to finish and a top coat of paint
i will try to post some piccys tomorrow after i pick it up,

Thanks for the warm welcome

vak1c100
Posts: 238
Joined: Mon Feb 27, 2006 10:08 pm
Location: Newark, England

Post by vak1c100 » Sat Aug 08, 2009 10:38 am

Hi glen

Our copmasters have no trouble running on the ab-2 plug and as joe90 has said they are a very reasonable price. Fan belts too wont break the bank but just make sure you specify that you don't have a belt driven dynamo and you should be well away.

Cant wait to see the pictures

Cheers

Lee

User avatar
glenreed
Posts: 24
Joined: Thu Aug 06, 2009 7:30 pm

Post by glenreed » Sat Aug 08, 2009 11:54 pm

Finaly got my cropmaster today, had a tinker for a couple of hours and found a couple of things..... panels dont seem to line up very well (main bonnnet to rad grill) nothing major and i cant seem to find any bolts in my workshop to fit anything, would it have BSF nuts and bolts?? also i think the throttle linkage from the hand control to the govener is missing if anyone has a picture of theres it would be a great help and there isnt any wiring on it at all except for the main lead from the starter which i assume goes to the possitive battery terminal... can anyone advise how to wire the dynamo reg? and does the ignition switch just earth out the mag when in the off position??

Post Reply

Who is online

Users browsing this forum: No registered users and 38 guests