Venting of 885 Final Drives

The place to discuss all matters relating to David Brown Tractors. You will need to register your user name before you can post. If you have already registered could you please make sure that your location details have been completed. Go to My Account in the Main Menu on the left, and then go into "Edit Your Information" and complete your location details. Give the Country (and State/Province if you wish) if outside the U.K. County if within the U.K. Location details helps other members if you need spares, technical advice, or the nearest practical help.

DISCLAIMER -

David Brown Tractor Club Ltd
Forum/website Disclaimer

1. This [forum/website/chat room] and the advice and opinions expressed herein is not a solution for mechanical, electrical, valuations, other problems, breakdowns or issues experienced in relation to the vehicles referenced.

2. If reliance is thought to be placed on any of the information guidance or input provided such information will be expressly confirmed as appropriate to be relied upon.

3. In the absence of any such confirmation no reliance should be suggested or inferred.

4. Members must not disclose information to 3rd parties in anticipation that reliance will be given by non-members.

5. Non-members must not purport to give advice on behalf of David Brown Tractor Club.

6. If you or someone you know is experiencing difficulties or repeated breakdowns you must seek assistance for an appropriately qualified expert who holds themselves out as such.

7. Any comments are free of charge and made or posted on an ex gratia basis. No member or non-member may advertise their professional services

Any user inactive for more than 3 months will automatically be deactivated, please contact admin@dbtc.co.uk if you would like to be reactivated.

Please be aware that your user name and entered location can be seen by all members. We only store information you have entered which is your email address and username, your IP is also stored, we have no access to private passwords.

If you do not agree with your information being stored, please do not register an account, If you wish to unsubscribe at any time please email admin@dbtc.co.uk giving your username.

Amended 27/10/18

Moderators: Segrie61, admin

Post Reply
ScottUSA
Posts: 64
Joined: Mon Mar 26, 2018 1:59 pm
Location: North Carolina

Venting of 885 Final Drives

Post by ScottUSA » Mon Feb 18, 2019 6:47 pm

I call them Final Drives but think they may be referred to as Drop Boxes, Reducing or Reduction Units. A quick search didn't help and my lunch hour is about up so… It's Final Drive for now.

When cleaning both final drives while replacing the tractors brakes, one unit was accidently left resting upside down. A spot of gear oil was found and investigation showed the oil to have come from what seems to be the vent. There is a 3/4" hex (1/2" bolt?) with a hole in it near the top of the rear facing plate on the final drive above the oil level drain and fill plugs. Is this intended to be the vent and is there anything more to it than a hole? What keeps dirt, bugs and rain water from entering?

User avatar
db2d
Posts: 2093
Joined: Fri Feb 24, 2012 10:01 pm
Location: Monmouthshire

Re: Venting of 885 Final Drives

Post by db2d » Mon Feb 18, 2019 7:37 pm

It is purely a vent and should periodically cleaned to keep it clear

tomryall
Posts: 148
Joined: Sun Jun 03, 2007 4:53 am
Location: canada

Re: Venting of 885 Final Drives

Post by tomryall » Tue Feb 19, 2019 12:24 am

this bolt should be at the top of the reduction housing

User avatar
cobbadog
Posts: 610
Joined: Tue Oct 11, 2011 6:18 am
Location: beautiful Coopernook NSW. near Taree. NSW. Australia

Re: Venting of 885 Final Drives

Post by cobbadog » Tue Feb 19, 2019 5:46 am

When I did the same maintenance on my 30C the same holes were blocked. So I took them out and over to the bench and using a twist drill bit by hand cleaned out the blockage. All is good now. Also if you didn't notice there are holes in the housing imediately below the brake linings. Clear these out as it allows any oil if it leaks to drain out insted of drowning your new linings.

Post Reply

Who is online

Users browsing this forum: db2d and 9 guests