1194 ignition switch wiring diagram

The place to discuss all matters relating to David Brown Tractors. You will need to register your user name before you can post. If you have already registered could you please make sure that your location details have been completed. Go to My Account in the Main Menu on the left, and then go into "Edit Your Information" and complete your location details. Give the Country (and State/Province if you wish) if outside the U.K. County if within the U.K. Location details helps other members if you need spares, technical advice, or the nearest practical help.

DISCLAIMER -

David Brown Tractor Club Ltd
Forum/website Disclaimer

1. This [forum/website/chat room] and the advice and opinions expressed herein is not a solution for mechanical, electrical, valuations, other problems, breakdowns or issues experienced in relation to the vehicles referenced.

2. If reliance is thought to be placed on any of the information guidance or input provided such information will be expressly confirmed as appropriate to be relied upon.

3. In the absence of any such confirmation no reliance should be suggested or inferred.

4. Members must not disclose information to 3rd parties in anticipation that reliance will be given by non-members.

5. Non-members must not purport to give advice on behalf of David Brown Tractor Club.

6. If you or someone you know is experiencing difficulties or repeated breakdowns you must seek assistance for an appropriately qualified expert who holds themselves out as such.

7. Any comments are free of charge and made or posted on an ex gratia basis. No member or non-member may advertise their professional services

Any user inactive for more than 3 months will automatically be deactivated, please contact admin@dbtc.co.uk if you would like to be reactivated.

Please be aware that your user name and entered location can be seen by all members. We only store information you have entered which is your email address and username, your IP is also stored, we have no access to private passwords.

If you do not agree with your information being stored, please do not register an account, If you wish to unsubscribe at any time please email admin@dbtc.co.uk giving your username.

Amended 27/10/18

Moderators: Segrie61, admin

Post Reply
User avatar
zombie25
Posts: 2
Joined: Fri Nov 25, 2016 4:54 pm
Location: Armstrong
Contact:

1194 ignition switch wiring diagram

Post by zombie25 » Fri Nov 25, 2016 5:12 pm

Hi everyone,
Does anyone have an ignition switch wiring diagram? The dealership here has several but different colour codes to what I have. The tractor will start but when turning the key on there are no dash lights, dash lights come on when I get to the pre-heat position then off as normal when tractor is running. Colours of wire, big brown, big red white,green, red white.
I have it hooked up brown on top, red on bottom, green/white ( separate wires to same terminal, wires on right as you sit in the tractor, red/white on left. Any help would be appreciated.
Regards David

User avatar
mistermcgregor
Posts: 157
Joined: Sat Sep 08, 2012 10:09 pm
Location: Southampton

RE: 1194 ignition switch wiring diagram

Post by mistermcgregor » Fri Nov 25, 2016 5:55 pm

The switch is probably faulty. This fault is not uncommon.

User avatar
case-ih1594
Posts: 1065
Joined: Sun May 12, 2013 10:38 am
Location: Preston

RE: 1194 ignition switch wiring diagram

Post by case-ih1594 » Fri Nov 25, 2016 6:20 pm

There is a diagram here:

http://www.dbtc.co.uk/index.php?module= ... 51&mid=490

The ignition section will probably be the same as yours, it is a basic system.

JamesF
Posts: 1327
Joined: Tue Mar 14, 2006 8:49 pm
Location: South Yorkshire

RE: 1194 ignition switch wiring diagram

Post by JamesF » Fri Nov 25, 2016 10:20 pm

Big brown wire goes to terminal 1, this is the live feed. Red also goes to terminal one and gives a live feed to the hazard switch

White wire and green go to terminal two, these wires go to the warning lights and instruments and indicator/blower switch etc

The red/white wire is the starter wire and goes to terminal 4 of the key switch

You should have another heavy wire connected to terminal 3 of the key switch which is the heater plug wire

If you only get the dash lamps when the key is turned to the pre heat position it's most likely connected up incorrectly

User avatar
zombie25
Posts: 2
Joined: Fri Nov 25, 2016 4:54 pm
Location: Armstrong
Contact:

Post by zombie25 » Sun Nov 27, 2016 7:33 pm

Thank you for the replies, and the help is much appreciated.
Regards David

Post Reply

Who is online

Users browsing this forum: jazo and 21 guests