Clutch master cylinder.

The place to discuss all matters relating to David Brown Tractors. You will need to register your user name before you can post. If you have already registered could you please make sure that your location details have been completed. Go to My Account in the Main Menu on the left, and then go into "Edit Your Information" and complete your location details. Give the Country (and State/Province if you wish) if outside the U.K. County if within the U.K. Location details helps other members if you need spares, technical advice, or the nearest practical help.

DISCLAIMER -

David Brown Tractor Club Ltd
Forum/website Disclaimer

1. This [forum/website/chat room] and the advice and opinions expressed herein is not a solution for mechanical, electrical, valuations, other problems, breakdowns or issues experienced in relation to the vehicles referenced.

2. If reliance is thought to be placed on any of the information guidance or input provided such information will be expressly confirmed as appropriate to be relied upon.

3. In the absence of any such confirmation no reliance should be suggested or inferred.

4. Members must not disclose information to 3rd parties in anticipation that reliance will be given by non-members.

5. Non-members must not purport to give advice on behalf of David Brown Tractor Club.

6. If you or someone you know is experiencing difficulties or repeated breakdowns you must seek assistance for an appropriately qualified expert who holds themselves out as such.

7. Any comments are free of charge and made or posted on an ex gratia basis. No member or non-member may advertise their professional services

Any user inactive for more than 3 months will automatically be deactivated, please contact admin@dbtc.co.uk if you would like to be reactivated.

Please be aware that your user name and entered location can be seen by all members. We only store information you have entered which is your email address and username, your IP is also stored, we have no access to private passwords.

If you do not agree with your information being stored, please do not register an account, If you wish to unsubscribe at any time please email admin@dbtc.co.uk giving your username.

Amended 27/10/18

Moderators: Segrie61, admin

Post Reply
User avatar
wheelbarrow
Posts: 23
Joined: Mon Nov 04, 2013 3:48 pm
Location: Cardigan Ceredigion

Clutch master cylinder.

Post by wheelbarrow » Sat Jun 07, 2014 1:26 pm

Hi folks
I need to take out and repair my clutch master cylinder, I've tried searching but that feature doesn't seen to work for me. Basically from which side do I attack this job, either in cab behind the panels under the steering or have I to become a contortionist and try to get it from somewhere I between loader and cab. Nearly forgot tractor is a 1973 1190.
Thanks as always

Guest

RE: Clutch master cylinder.

Post by Guest » Sat Jun 07, 2014 1:53 pm

You have to move the dash pod back to get at it which requires disconnecting the hand throttle, the stop cable, possibly the wiring harness connector, the set screws each side of the pod and you may also have to remove the steering wheel to lift the pod enough to clear the fluid reservoirs. Also don't forget that LHM mineral fluid is the correct stuff to put in the reservoir, both clutch and brake.

User avatar
ollek
Posts: 3938
Joined: Tue Apr 10, 2012 1:20 pm
Location: South West Finland

RE: Clutch master cylinder.

Post by ollek » Sat Jun 07, 2014 3:00 pm

For the repair, do as Powerrabbit says. But for your knowledge, if the tractor is a 1190, it has to be from between 1980 and 1984.

User avatar
case-ih1594
Posts: 1065
Joined: Sun May 12, 2013 10:38 am
Location: Preston

RE: Clutch master cylinder.

Post by case-ih1594 » Sat Jun 07, 2014 3:04 pm

Hi, further to Powerrabbits advice, you need to be very careful not to damage the dash - so many have been broken and they are very brittle.

It is probably best to remove the steering wheel and SLOWLY lift off (upwards and towards the driver), the entire plastic dash / console. Replacing the brake master seals whilst you are there may be a good insurance policy.

You should be able to get away without removing the stop cable. The job is not difficult but you need to check and double check everything or damage will occur.

Presumably you mean the tractor is an 1983 DB 1190 :lol: (ollek got there first!)

User avatar
wheelbarrow
Posts: 23
Joined: Mon Nov 04, 2013 3:48 pm
Location: Cardigan Ceredigion

RE: Clutch master cylinder.

Post by wheelbarrow » Sat Jun 07, 2014 5:18 pm

Yes she is an 83, fat fingers and small keyboard don't mix. Thanks for all the replies, just waiting for the repair kit to come in hopefully the bores in the cylinder are good.
:D
Current shed contents
1983 David Brown 1190
1963 Massey 35x been in the family from new.
Massey Ferguson 50 H digger. Better than a spade

Post Reply

Who is online

Users browsing this forum: Google [Bot] and 8 guests