Cropmaster Crank handle

The place to discuss all matters relating to David Brown Tractors. You will need to register your user name before you can post. If you have already registered could you please make sure that your location details have been completed. Go to My Account in the Main Menu on the left, and then go into "Edit Your Information" and complete your location details. Give the Country (and State/Province if you wish) if outside the U.K. County if within the U.K. Location details helps other members if you need spares, technical advice, or the nearest practical help.

DISCLAIMER -

David Brown Tractor Club Ltd
Forum/website Disclaimer

1. This [forum/website/chat room] and the advice and opinions expressed herein is not a solution for mechanical, electrical, valuations, other problems, breakdowns or issues experienced in relation to the vehicles referenced.

2. If reliance is thought to be placed on any of the information guidance or input provided such information will be expressly confirmed as appropriate to be relied upon.

3. In the absence of any such confirmation no reliance should be suggested or inferred.

4. Members must not disclose information to 3rd parties in anticipation that reliance will be given by non-members.

5. Non-members must not purport to give advice on behalf of David Brown Tractor Club.

6. If you or someone you know is experiencing difficulties or repeated breakdowns you must seek assistance for an appropriately qualified expert who holds themselves out as such.

7. Any comments are free of charge and made or posted on an ex gratia basis. No member or non-member may advertise their professional services

Any user inactive for more than 3 months will automatically be deactivated, please contact admin@dbtc.co.uk if you would like to be reactivated.

Please be aware that your user name and entered location can be seen by all members. We only store information you have entered which is your email address and username, your IP is also stored, we have no access to private passwords.

If you do not agree with your information being stored, please do not register an account, If you wish to unsubscribe at any time please email admin@dbtc.co.uk giving your username.

Amended 27/10/18

Moderators: Segrie61, admin

Post Reply
User avatar
prblake
Posts: 160
Joined: Wed Aug 25, 2010 1:52 pm
Location: Queensland, Australia

Cropmaster Crank handle

Post by prblake » Thu Oct 10, 2013 6:00 am

After a long time looking here in Australia I have not been able to find a crank handle so i have decided to make one. Over the years I have been given two drawings. One says the handle is 5/8" (16mm) round bar and the other says 3/4" (19mm) round bar.

Could someone who has the proper Croppy crank handle check the diametre of the bar it is made from please.

I have all the other dimensions.

Paul

User avatar
prblake
Posts: 160
Joined: Wed Aug 25, 2010 1:52 pm
Location: Queensland, Australia

Cropmaster Crank handle

Post by prblake » Thu Oct 17, 2013 6:51 am

Any chance someone has a crank handle and can measure it for me please. I just need to know the diametre of the crank handle so I can make one.

Thanks so much if you can help.

Paul

User avatar
db2d
Posts: 2198
Joined: Fri Feb 24, 2012 10:01 pm
Location: Monmouthshire

RE: Cropmaster Crank handle

Post by db2d » Thu Oct 17, 2013 7:12 am

I will measure one today and reply tonight.

User avatar
prblake
Posts: 160
Joined: Wed Aug 25, 2010 1:52 pm
Location: Queensland, Australia

RE: Cropmaster Crank handle

Post by prblake » Thu Oct 17, 2013 9:43 pm

Thanks very much for your help db2d.

Paul

User avatar
powercropmaster
Posts: 9
Joined: Mon Sep 10, 2012 12:50 am
Location: Quebec, Canada

Post by powercropmaster » Thu Oct 24, 2013 8:04 pm

I own the crank handle used for my Cropmaster diesel 30D the size of the crank is 3/4" and the pin to engage in the crankshaft nut is 5/16" X 1"3/4 it measures 20"until the90degrees angle 10"3/4 and 6"1/2 on the handle

Jean-Paul

User avatar
prblake
Posts: 160
Joined: Wed Aug 25, 2010 1:52 pm
Location: Queensland, Australia

Post by prblake » Mon Oct 28, 2013 10:34 pm

Thanks for the information Jean-Paul. I can get on with my project now.

Paul

Post Reply

Who is online

Users browsing this forum: No registered users and 21 guests