Search found 763 matches

by jazo
Tue Jun 19, 2018 7:50 am
Forum: DBTC Forum
Topic: 1212 Front Loaders.
Replies: 24
Views: 3921

Re: 1212 Front Loaders.

Hi it's fine to do but you only have one reverse and 3 forward gears to choose from when starting off as you have to have the hydrashift in 1st. Most hydrashift tractors in new Zealand have loaders fitted! Use it as it should be and it will be fine. Sorry can't answer your question though!
by jazo
Fri Jun 08, 2018 8:33 am
Forum: DBTC Forum
Topic: Cleaning cooling system
Replies: 2
Views: 715

Re: Cleaning cooling system

Hi. If its rusty I use white vinegar, I leave it in for a couple days then flush. Repeat if necessary. Use about 4 litres of it and the rest water.
by jazo
Fri Jun 01, 2018 9:14 pm
Forum: DBTC Forum
Topic: 1490. Two versions of hydraulic strainer?
Replies: 4
Views: 832

Re: 1490. Two versions of hydraulic strainer?

I think it was the 1210 and the like models had paper and gauze filters. I know there isn't much room but if you can get a bar on each side of the filter and have 2 people pushing on it equally it will certainly help. You will need the powerbar that slides through the head type, sorry don't know the...
by jazo
Tue May 29, 2018 7:48 am
Forum: DBTC Forum
Topic: Rear arms not dropping low
Replies: 8
Views: 1221

Re: Rear arms not dropping low

Hi try removing the cover behind your right foot that has the lowering speed control knob and there is a 1/2" size nut in there. Unwind when it's running might only take a couple turns to lower correctly
by jazo
Tue May 22, 2018 8:23 pm
Forum: DBTC Forum
Topic: 1490 loader issues.
Replies: 9
Views: 1432

Re: 1490 loader issues.

Hi. Have did you had any weight on the lift arms when you checked there operation? Maybe the pump is sucking air in the inlet or gauze is blocked?
by jazo
Mon May 14, 2018 9:26 pm
Forum: DBTC Forum
Topic: 990 Fuel Pump
Replies: 18
Views: 3074

Re: 990 Fuel Pump

Hi as mentioned earlier you can just undo the 6 screws and rotate around to your desired position
by jazo
Tue Apr 24, 2018 7:36 pm
Forum: DBTC Forum
Topic: David Brown 2012
Replies: 12
Views: 2437

Re: David Brown 2012

That's a 1290 or 1390
by jazo
Fri Apr 20, 2018 8:32 pm
Forum: DBTC Forum
Topic: Round baler for David Brown 990 Selectamatic
Replies: 19
Views: 3715

Re: Round baler for David Brown 990 Selectamatic

Hi, I have baled with a 3/45 Nuffield (45hp) before with an gehl 1475 baling 4x4 silage bales. It drove it ok just slower that's all. Hay would be alot easier
by jazo
Thu Mar 15, 2018 2:34 am
Forum: DBTC Forum
Topic: Bent/Broken Push Rods
Replies: 25
Views: 5360

Re: Bent/Broken Push Rods

Give it some hard work to bed it in after rebuild. Diesels need to be worked hard
by jazo
Mon Feb 26, 2018 6:58 am
Forum: DBTC Forum
Topic: 880 started running rough
Replies: 53
Views: 8716

Re: 880 started running rough

Hi sounds like the injector pump timing is a bit out. I would check it out first before sending away
by jazo
Thu Feb 08, 2018 6:00 pm
Forum: DBTC Forum
Topic: 885 selectamatic
Replies: 41
Views: 7994

Re: 885 selectamatic

That part looks very straight and original!
by jazo
Wed Feb 07, 2018 7:08 am
Forum: Members Restorations
Topic: Bringing a 1212 back
Replies: 4
Views: 1424

Re: Bringing a 1212 back

Hi, will be a great project for you!
by jazo
Wed Jan 31, 2018 7:11 am
Forum: DBTC Forum
Topic: Hydraulic filter on fitting problem on 990
Replies: 5
Views: 1400

Re: Hydraulic filter on fitting problem on 990

Hi, I also have this problem with aftermarket filters. I replace the oring off the filter with a better fitting one from one of my kits, then they seam to work ok
by jazo
Wed Jan 31, 2018 12:10 am
Forum: DBTC Forum
Topic: 990 selectamatic pointer fork replacement
Replies: 3
Views: 771

Re: 990 selectamatic pointer fork replacement

Hi, no it needs setting to exactly the size etched into the end of the spool. You will need a dial gauge with magnetic base to do this.
by jazo
Sat Jan 27, 2018 9:21 pm
Forum: DBTC Forum
Topic: New tractor 1594
Replies: 3
Views: 773

Re: New tractor 1594

All one oil