Search found 13 matches

by laubaeh
Wed Aug 28, 2019 10:40 pm
Forum: DBTC Forum
Topic: Engine swap 996 1390
Replies: 0
Views: 3473

Engine swap 996 1390

Hello Folks, I have a 996 4WD with a carraro front axle. Engine oil pressure was poor. I changed the big end con rod bearings and the middle main crank bearing. Pressure is now better (aprox 1 bar / 14,5 psi) when temperature gauge shows 1/3 green. When it goes to 2/3 green pressure dropps to 0,5 ba...
by laubaeh
Mon Apr 08, 2019 9:49 pm
Forum: DBTC Forum
Topic: Power steering leak
Replies: 0
Views: 4016

Power steering leak

Hello everyone, I have a 996 (from 1979) with CAB. Now the Orbitrol Valve (K946083) is leaking. Question: Can I use K207419 instead of K946083) ? Some sellers say so. Can anyone think of a way to change the valve without removing the CAB ? I thought about cutting a hole in the console, change the va...
by laubaeh
Sun Sep 24, 2017 5:59 pm
Forum: DBTC Forum
Topic: 996 4wd Carraro axle
Replies: 1
Views: 752

Re: 996 4wd Carraro axle

Hello everbody The front axle ist back togehther. You can pull the driveshaft's out, no poroblem. Just a bit more pulling and hitting the bearing with a hammer and a chissel. I got the holes in the axle housing bigger and I got new oversized bearing pins. Erverthing is back together. But I've got a ...
by laubaeh
Sun Aug 27, 2017 7:59 pm
Forum: DBTC Forum
Topic: 996 4wd Carraro axle
Replies: 1
Views: 752

996 4wd Carraro axle

Hello everbody, I've got a 996 4wd with a Carraro front axle and power steering. The reducion hubs were leaking, so I replaced gaskets and seals and put the right side back together. Also fitted in a pair of bearings for the bearing pin. So far so good Then I started the left side, and the problems ...
by laubaeh
Tue Aug 11, 2015 5:21 pm
Forum: DBTC Forum
Topic: Front Wheel 996
Replies: 0
Views: 1428

Front Wheel 996

Hello,

I am looking for a front wheel (just the rim) for a 996 4WD tractor.

It is a MK3 with the Carraro axle.

Any Ideas where I can get one ?


Best Regards

Ralf

from Germany
by laubaeh
Wed Mar 11, 2015 11:40 am
Forum: DBTC Forum
Topic: 996 hydraulic filter switch
Replies: 4
Views: 3014

I replaced the filter, it's new.


I'll try to check the new switch with a vacuum pump.


I think I got the wrong switch.
by laubaeh
Wed Mar 11, 2015 11:37 am
Forum: DBTC Forum
Topic: Safety switch on a 996
Replies: 6
Views: 3886

I don't remebmber any shims but I'll try.

I think they sold me the wrong switch.

Thanks for your Help

Rlaf
by laubaeh
Tue Mar 10, 2015 10:49 pm
Forum: DBTC Forum
Topic: Safety switch on a 996
Replies: 6
Views: 3886

Safety switch on a 996

Hello again,


I replaced the safety switch on the gearbox last year.

Now the traktor starts only when the gears ar NOT in neutral.

Is this correct?

Thanks for your help


Ralf
by laubaeh
Tue Mar 10, 2015 10:45 pm
Forum: DBTC Forum
Topic: 996 hydraulic filter switch
Replies: 4
Views: 3014

996 hydraulic filter switch

Hello everybody I have a 996 The orange light for the hydraulic oil filter warning is on. I got a new switch, k921317 Is this a pressure switch or a vacuum switch ? It has .55 bar writen on it. I mesured a short without pressure. When i put it into compressed air it opens. Is this right ? Thanks for...
by laubaeh
Wed Aug 06, 2014 7:46 pm
Forum: DBTC Forum
Topic: David Brown 996 Hydraulics question
Replies: 4
Views: 4672

RE: David Brown 996 Hydraulics question

OK, Thanks for the info. I will change the loader to port #1 on the 3 way valve. Is there a posibility to get presure oil independet of the mail control lever ? I do not have the auxilary double acting valves (i think they are monted instead of the "camel hubs") installed. Would this be a posibility...
by laubaeh
Tue Aug 05, 2014 6:55 pm
Forum: DBTC Forum
Topic: David Brown 996 Hydraulics question
Replies: 4
Views: 4672

David Brown 996 Hydraulics question

Hello everybody, I have a DB 996 with a Sekura Cab and a loader. The 996 is from 1979 an a Selectamatic. The loader has extra electric control valves with no flow in neutral (to tank) Loader is connected to the "camel hubs" 3 way valve (left side): Port 2 for tipping cart ; port 1 has an sealing plu...
by laubaeh
Fri Jul 18, 2014 1:41 pm
Forum: DBTC Forum
Topic: - urgent - Reduction hub 885 on 966 - urgent -
Replies: 5
Views: 2424

- urgent - Reduction hub 885 on 966 - urgent -

Hallo,

My name mis Ralf, i an new here an I have a question:

I have been offerd a reduction hub of an 885. Can I use it on my 996 ?


Bye for now,


Ralf