Search found 398 matches

by GeoffDEAL
Sun Jun 23, 2019 10:09 pm
Forum: DBTC Forum
Topic: 90 series with bale wappers
Replies: 4
Views: 99

Re: 90 series with bale wappers

Hi used my 1394 on a 654 New Holland some years ago and worked alright, was usually using a 1494 at the time and now use the 1690t for baling. There was little difference between the 1394 and the 1494 as the 1494 is without its turbo .
by GeoffDEAL
Wed Jun 19, 2019 10:09 pm
Forum: DBTC Forum
Topic: Beware 1412 exhaust on ebay
Replies: 7
Views: 239

Re: Beware 1412 exhaust on ebay

Hi if you make a hole in the plate in muffler make one in the center then use a pointed bar --crow bar to enlarge the hole to full size there should be no restriction on a turbo muffler straight through full size, bump the muffler and pointed bar on a block of wood should go through with a bit of ef...
by GeoffDEAL
Sat Jun 08, 2019 3:25 am
Forum: DBTC Forum
Topic: DB 1200
Replies: 18
Views: 936

Re: DB 1200

Hi is fuel coming out if you loosen injector pipes, if the stop on injection pump doesnt work it can indicate the rack in the pump is sticking or stuck, this also affects the supply of fuel to the injectors, take the side cover off and see what is going on-- throttle movement --stop--and extra fuel ...
by GeoffDEAL
Mon May 27, 2019 9:43 pm
Forum: DBTC Forum
Topic: Timing Gears
Replies: 6
Views: 317

Timing Gears

I was recently asked if they are available for a 995 but i have never done any since my 1200 many years ago when such parts were available and would think scrap motors would be the main source in our part of the world. Appears to be one of the few parts not available after market that one cannot get...
by GeoffDEAL
Sat May 25, 2019 10:47 am
Forum: DBTC Forum
Topic: Side Panels
Replies: 2
Views: 209

Re: Side Panels

Hi they look really good, i wonder how DB did the louvers on side panels on some tractors like the crawlers there are several different ones and different numbers of louvers and spacing.
by GeoffDEAL
Sat May 25, 2019 10:41 am
Forum: DBTC Forum
Topic: 1690T reduction ratios ...
Replies: 6
Views: 519

Re: 1690T reduction ratios ...

The 1690t with 18.4 --38 have 14.9 --24 front tyres where the 34" rears have 13.6 -24 fronts to keep the ratio correct also there can be different profile of the back and front tyres depending on what tyres are fitted.
by GeoffDEAL
Sat May 18, 2019 10:31 pm
Forum: DBTC Forum
Topic: Cropmaster Fuel Issue
Replies: 2
Views: 172

Re: Cropmaster Fuel Issue

Hi does it make any difference if the tap is on reserve or main supply? or maybe some dirt got dislodged when you removed the tap and got to the carb maybe check and give it a clean, First remove outlet pipes and move tap to see if fuel is running on positions.
by GeoffDEAL
Wed May 15, 2019 10:20 pm
Forum: DBTC Forum
Topic: Oliver 500 & Oliver 600
Replies: 3
Views: 280

Re: Oliver 500 & Oliver 600

Hi Gregory the 500 went from Ser no 100001 Feb 1960 to Ser 102148 May 1963 -- the 600 from Ser 449800 Dec 1962 to Ser 453700 May 1963 so not so many of the 500s, there is very few in New Zealand eaither brought in later or different grill and paint on red ones. cheers Geoff
by GeoffDEAL
Wed May 08, 2019 10:28 pm
Forum: DBTC Forum
Topic: 1394 steering fluid change
Replies: 7
Views: 506

Re: 1394 steering fluid change

Hi as in previous post yes un doing the pipes and operating the steering will drain the system, the filter is in the housing where you fill the oil remove this to get to the filter-- will most likely need a new o ring where it fits on, filters are available from Sparex and other suppliers, system is...
by GeoffDEAL
Tue May 07, 2019 10:45 pm
Forum: DBTC Forum
Topic: 30td
Replies: 3
Views: 220

Re: 30td

Hi ljd its a bit far away for me at Ashburton with that expensive bit of water between islands, the diesels are quite rare, so dont scrap it, put it on Trademe and will be sure to sell and someone enjoy it. cheers Geoff
by GeoffDEAL
Mon May 06, 2019 10:55 am
Forum: DBTC Forum
Topic: 30td
Replies: 3
Views: 220

Re: 30td

Hi where abouts are you in NZ .cheers Geoff
by GeoffDEAL
Sun May 05, 2019 10:01 pm
Forum: DBTC Forum
Topic: DB 1200
Replies: 18
Views: 936

Re: DB 1200

Hi probably a good idea to change the fuel filters if its been sitting a while, try pressing the cold start button in the injection pump, needs the throttle leaver at part revs position as cold start doesnt click in at idle, you should hear a click when pressed in, that means the fuel control rack i...
by GeoffDEAL
Wed May 01, 2019 10:28 am
Forum: DBTC Forum
Topic: 1690T reduction ratios ...
Replies: 6
Views: 519

Re: 1690T reduction ratios ...

Hi Ian the ratio should be stamped on the center of the back axel sometimes a bit hard to see with the paint.
by GeoffDEAL
Tue Apr 30, 2019 1:15 am
Forum: DBTC Forum
Topic: DB 1200
Replies: 18
Views: 936

Re: DB 1200

Hi ollek if the hydraulics are on lift at start oil and air will be pumped to the lift cylinder, if not on lift oil and air will circulate back to gearbox untill just oil is circulating then would be the time to start using the lift. I guess if the cylinder reaches the top with leaver on lift it sho...
by GeoffDEAL
Mon Apr 29, 2019 12:45 am
Forum: DBTC Forum
Topic: By-pass valve removal tip
Replies: 10
Views: 445

Re: By-pass valve removal tip

Hi it was part of the first service on DB 1200 the valves were removed by service man and polished with fine wet and dry paper to remove any marks from the new valves slightly sticking i was told at the time, the tractor has had no valve problems to this day. I would think it would take a long time ...