Search found 171 matches

by tomryall
Thu Jun 25, 2020 1:28 pm
Forum: DBTC Forum
Topic: 990 PTO shaft
Replies: 3
Views: 170

Re: 990 PTO shaft

If it has a bolt and special washer on the end of the shaft you should use loctite on the threads , from memory I think it was a allen screw that was used,a new one used to have loctite already applied.
by tomryall
Thu Jun 18, 2020 3:03 am
Forum: DBTC Forum
Topic: Warning bulbs, David Brown 1200 dashboard
Replies: 8
Views: 256

Re: Warning bulbs, David Brown 1200 dashboard

the bulb and holder are pushed out from the back, then you pull the holder off the bulb , they can be tricky may be corroded and the holder can be brittle but if you have new ones ordered you will be ok.
by tomryall
Wed Jun 17, 2020 1:44 pm
Forum: DBTC Forum
Topic: 25c Repairs
Replies: 14
Views: 398

Re: 25c Repairs

I have cleaned a Croppy with the same mess, took off the pto housing and gearbox cover and the used a steam cleaner, it took a while to get everything clean ,then I blew it out with 3/4"airline to get it all dry I also blew air through all the oil pipes. Good as new.
by tomryall
Tue Jun 16, 2020 1:42 am
Forum: DBTC Forum
Topic: Question regarding 885N indicator warning bulbs
Replies: 5
Views: 216

Re: Question regarding 885N indicator warning bulbs

IF you can get your hand up behind the dash the bulb holders should push out , they might be gone hard and brittle and break easily , David Brown Parts have replacements , I have just fitted 3 to one of my 885's . the easiest way to remove the dash is first remove the steering column just 4 bolts to...
by tomryall
Sun Jun 14, 2020 2:10 pm
Forum: DBTC Forum
Topic: steeringpump David Brown
Replies: 13
Views: 351

Re: steeringpump David Brown

As far as I know the pump on the left is belt driven off a pulley bolted onto the pulley that drives the water pump and alternator , at least that is the way it is on my 885's . it should be easy to get or adept a pulley to suit . I can measure the diameter if you want.I believe these pumps are no l...
by tomryall
Fri Jun 12, 2020 3:11 am
Forum: DBTC Forum
Topic: 25c Repairs
Replies: 14
Views: 398

Re: 25c Repairs

It might be a good idea to strip down the king pins and clean them up , then you can check the thrust washers , I was able to get a thrust bearing to replace the washers, it is a help . grease should not be used on the king pins or trunnion shaft DB recommends 140 oil. A second grease gun for this i...
by tomryall
Thu Jun 11, 2020 1:05 am
Forum: DBTC Forum
Topic: Leaking Hydraulic Pipe Bypass? on 885/1
Replies: 2
Views: 146

Re: Leaking Hydraulic Pipe Bypass? on 885/1

That unit is called a Cessna valve , a seal kit is available from David Brown Parts. Be careful when opening the end as there is a spring and 3 small balls in there, wrap a rag around the cap as you take it off that way you will not loose the balls. Open the clip at the other end and you can then re...
by tomryall
Fri May 15, 2020 2:15 am
Forum: DBTC Forum
Topic: Recommended Professional DB refurbisher? Advice please
Replies: 5
Views: 392

Re: Recommended Professional DB refurbisher? Advice please

I must apologise , when I saw Halifax I immediately thought of Halifax Nova Scotia I should have realised there is also a Halifax In England.
A tractor in Canada might be a bit far away, But I have sent many tractors back to Ireland.
by tomryall
Wed May 13, 2020 11:46 pm
Forum: DBTC Forum
Topic: Recommended Professional DB refurbisher? Advice please
Replies: 5
Views: 392

Re: Recommended Professional DB refurbisher? Advice please

I might be able to help I have a few different models of Cropmaster, send me a pm and I will email or phone you. I am in Manitoba
by tomryall
Sat May 09, 2020 2:42 pm
Forum: DBTC Forum
Topic: Sourcing Glass Fuel Bowl - 780 Selectamatic
Replies: 6
Views: 374

Re: Sourcing Glass Fuel Bowl - 780 Selectamatic

I made one using a piece of 2"round nylon bar , if you have a lathe it is no problem, or somebody with a lathe could make one, mine has worked perfect for 3 or 4 years.
by tomryall
Tue May 05, 2020 2:00 pm
Forum: DBTC Forum
Topic: Case 380Ck/Db 885 Hydraulic Filter
Replies: 13
Views: 603

Re: Case 380Ck/Db 885 Hydraulic Filter

I had the same problem on my 885 , I made a extension out of a piece round nylon bar to fit over the filter and into the suction pipe.
a lot of after market stuff is problematic.
by tomryall
Fri May 01, 2020 12:59 am
Forum: DBTC Forum
Topic: 780 selectamatic hydraulic problems
Replies: 6
Views: 508

Re: 780 selectamatic hydraulic problems

Worn or loose friction washer at lower end of lift lever, tighten nut on lower end of lift lever , there is usually a lock nut on the shaft loosen the lock nut then tighten the inner nut until the lever stays where you put it , when you pull the lever back all the way against the spring it should mo...
by tomryall
Wed Apr 29, 2020 12:12 am
Forum: DBTC Forum
Topic: Where to buy parts?
Replies: 3
Views: 340

Re: Where to buy parts?

Your case dealer might or might not have some parts , they should be able to get some , but will likely be expensive . I use David Brown parts ltd in England Peter is very obliging and knowledegable and their parts are really good ,some of the other after market stuff out there is rubbish. if you go...
by tomryall
Wed Apr 15, 2020 8:15 pm
Forum: DBTC Forum
Topic: Smoky Exhaust / Elbow joint
Replies: 3
Views: 298

Re: Smoky Exhaust / Elbow joint

Maybe a faulty exhaust pipe.try a length of straight pipe to see what happens .
by tomryall
Tue Apr 14, 2020 11:43 pm
Forum: DBTC Forum
Topic: best way to attach trailer?
Replies: 12
Views: 782

Re: best way to attach trailer?

Hitching a trailer that far back is dangerous as the tractor could rear up and capsize causing serious injury or even death. a trailer should only be hitched to the tractor drawbar and the drawbar should be be the forward position , the rearward position is usually only used for PTO driven implement...