Search found 571 matches

by cobbadog
Tue Aug 13, 2019 7:14 am
Forum: DBTC Forum
Topic: 94' series 4wd components the same?
Replies: 13
Views: 351

Re: 94' series 4wd components the same?

So by the reply it would appear that it would not fit, unless you change over the complete transmission.
by cobbadog
Mon Aug 12, 2019 6:26 am
Forum: DBTC Forum
Topic: Hydraulics!!
Replies: 5
Views: 194

Re: Hydraulics!!

As always pictures help to understand your problem.
by cobbadog
Thu Aug 08, 2019 12:05 pm
Forum: DBTC Forum
Topic: Manifold flange removal.
Replies: 17
Views: 524

Re: Manifold flange removal.

I recently was shown a jar full of broken drill bits and the owner asked if I noticed anything unusual about them. No was my reply. He said look at the flukes on the drill bit they run the opposite direction. He had no idea of what they were so I asked around and found out that they are left handed ...
by cobbadog
Tue Aug 06, 2019 6:42 am
Forum: DBTC Forum
Topic: Ready for wet sand blasting
Replies: 29
Views: 1636

Re: Ready for wet sand blasting

Yes Gard, it was a serious bit of gear and worked so quick on the day. I did look at attachments that fit to your gernie and do wet sand blasting but they were small and I am not sure of how effective they would be. Having said that I then looked on good ol YouTube and watched some videos of these t...
by cobbadog
Mon Aug 05, 2019 12:04 pm
Forum: DBTC Forum
Topic: Manifold flange removal.
Replies: 17
Views: 524

Re: Manifold flange removal.

UNC die nut would not be expensive and more than likely sitting in a box of die nuts at a garage sale but
i can get them for around AU$15.00 then once clean assemble with some anti sieze and brass nuts.
by cobbadog
Mon Aug 05, 2019 7:20 am
Forum: DBTC Forum
Topic: Manifold flange removal.
Replies: 17
Views: 524

Re: Manifold flange removal.

Time to heat the nuts up and give it a try. There are no way of knowing what will happen until you try. Another option to try is to use eithe a nut splitter or if you have room use your angle grinder to cut the nuts on an angle down to near the thread and this might help release its grip. Obviously ...
by cobbadog
Sat Aug 03, 2019 6:18 am
Forum: DBTC Forum
Topic: If it's not one thing it's another. 885 starter drive #
Replies: 17
Views: 522

Re: If it's not one thing it's another. 885 starter drive #

No worries Scott, I didn't price a new bendix jsut found an after market starter motor whch is all that is available here as a replacemnt starter motor. No doubt somehwer I could buy a bendix for one if required. I looked at buying a new solenoid for the Hino starter motor. It has 3 wires that run t...
by cobbadog
Fri Aug 02, 2019 12:10 pm
Forum: DBTC Forum
Topic: If it's not one thing it's another. 885 starter drive #
Replies: 17
Views: 522

Re: If it's not one thing it's another. 885 starter drive #

This might be a case of same thing different name. Here we call them bendix drives but in the US it maybe what was descr4ibed as a pre-engaged type.
Another analagy would be generator and dynamo. It is because of these differing descriptions that things can get confusing.
by cobbadog
Fri Aug 02, 2019 7:00 am
Forum: DBTC Forum
Topic: If it's not one thing it's another. 885 starter drive #
Replies: 17
Views: 522

Re: If it's not one thing it's another. 885 starter drive #

WOW, you are super lucky over there, a starter motor for your tractor here is over AU$415.00 plus AU$40.00 postage here in Oz. No brand name on it or where it comes from either. Details on the solenoid are DEM902 12v-2.8 Kw with 11 teeth.
by cobbadog
Thu Aug 01, 2019 12:10 pm
Forum: DBTC Forum
Topic: Ready for wet sand blasting
Replies: 29
Views: 1636

Re: Ready for wet sand blasting

And as shown in the picture it does have the adjuster. At the age of these tractors now none of them would have an original generator / dynamo or starter motor so most out in the field after around ten years of age they too would have service exchanged electrics.
by cobbadog
Thu Aug 01, 2019 7:08 am
Forum: DBTC Forum
Topic: Ready for wet sand blasting
Replies: 29
Views: 1636

Re: Ready for wet sand blasting

Your wealth of knowledge is absolutely wonderful and is appreciated. Your comments "The rod from the hand control to the governor should have an adjustment connection in the middle." and it does have the adjuster so why make the comment? Then "There should be a spring inside the hydraulic quadrant."...
by cobbadog
Wed Jul 31, 2019 11:18 pm
Forum: DBTC Forum
Topic: Ready for wet sand blasting
Replies: 29
Views: 1636

Re: Ready for wet sand blasting

I was asked by private message to post details on the wet sand blaster. I dont have any specifications as to air and water pressures that are used to do the process but the water is pumped into the green hopper which has a mixer inside to keep the grit in solution and is forced through the line unde...
by cobbadog
Wed Jul 31, 2019 11:09 pm
Forum: DBTC Forum
Topic: Ready for wet sand blasting
Replies: 29
Views: 1636

Re: Ready for wet sand blasting

So I am guessing that it is alright for some to make critical comments and once you then discover that you were wrong you do not apologise. It certainly would have been a far better approach by you to ask the question/s if it had a spring or does it have an adjuster rather than being so very critica...
by cobbadog
Wed Jul 31, 2019 12:17 pm
Forum: DBTC Forum
Topic: Ready for wet sand blasting
Replies: 29
Views: 1636

Re: Ready for wet sand blasting

It does have an adjustment in the middle. It is just in front of the oil filter housing and behind the carby. It is the original left and right hand threaded adjuster with a lock nut.I asked you if the spring you mentioned for the hand control you claimed was missing is on this unit behind it betwee...
by cobbadog
Wed Jul 31, 2019 7:31 am
Forum: DBTC Forum
Topic: Ready for wet sand blasting
Replies: 29
Views: 1636

Re: Ready for wet sand blasting

Well here are the latest few pics for your enjoyment or annoyment depending on where you sit!

db2d, is the spring you refer to on the quadrant on the inside of it and would sit against the mudguard side?